Safety operation rules for automatic wire stripper
Source: Author: rsautomation88 Publish time: 2022-05-26 18:00 524 Views
Automatic wire stripper is a very popular wire harness processing equipment, complete functions, processing methods are more, such as cutting, peeling, half peeling, middle peeling, twisting and other functions can be achieved, a multi-purpose automatic wire stripper can be said to be a good helper of wire harness processing. How difficult is it to operate? This is a lot of people are very concerned about the problem, the following to give us a careful explanation of the automatic stripping machine safety operation procedures!
Automatic wire stripper is a very popular wire harness processing equipment, complete functions, processing methods are more, such as cutting, peeling, half peeling, middle peeling, twisting and other functions can be achieved, a multi-purpose automatic wire stripper can be said to be a good helper of wire harness processing. How difficult is it to operate? This is a lot of people are very concerned about the problem, the following to give us a careful explanation of the automatic stripping machine safety operation procedures!
One: before homework
1. Before operation, the operator shall strictly inspect the equipment according to the spot inspection system and make a good record;
2. Before starting the machine, check whether all accessories of the machine are correctly installed and confirm that there is no problem before starting the machine.
3. Confirm that the cutting line mold is in good condition, installation is reliable, and there is good lubrication;
Two: homework
1. According to the stripping length of cable and core wire required by the process document, adjust the position of the upper and lower (left and right) cutter, check whether the compressed air supply is normal, adjust the air flow of the cylinder, plug in the power supply, and control the device to start running with a foot switch.
2. After several pieces are cut, check the length and core wire quality of the product to ensure that the product conforms to the process document.
3. In the process of wire stripping, hands should not enter the inside of the protective cover, in case the machine hurts people.
4. Midway stop, please pull out the power plug, so that people leave, the machine power off, in case others mistakenly step on the pedal switch caused clamp injury.
5. If you need to replace a wire stripper blade, power off and cut off the air before replacing it.
6. If any abnormality is found in use, power off immediately and notify dedicated maintenance personnel for maintenance.
7. During the operation, the operator should concentrate, and do nothing unrelated to production is strictly prohibited.
Three: the end of the homework
1. After the execution of the production plan, the power supply of the equipment shall be turned off;
2. Turn off the main power supply of the equipment and clean the machine and surroundings before going off work.
Current machine automation age is more and more popular, people must have been more and more high to the requirement of wiring harness processing equipment, and automatic wire stripping machine technology is already very mature, so good understand relevant knowledge of mechanical equipment is also very necessary, hope this piece of wire stripping machine safety operation procedures can help to you.
One: before homework
1. Before operation, the operator shall strictly inspect the equipment according to the spot inspection system and make a good record;
2. Before starting the machine, check whether all accessories of the machine are correctly installed and confirm that there is no problem before starting the machine.
3. Confirm that the cutting line mold is in good condition, installation is reliable, and there is good lubrication;
Two: homework
1. According to the stripping length of cable and core wire required by the process document, adjust the position of the upper and lower (left and right) cutter, check whether the compressed air supply is normal, adjust the air flow of the cylinder, plug in the power supply, and control the device to start running with a foot switch.
2. After several pieces are cut, check the length and core wire quality of the product to ensure that the product conforms to the process document.
3. In the process of wire stripping, hands should not enter the inside of the protective cover, in case the machine hurts people.
4. Midway stop, please pull out the power plug, so that people leave, the machine power off, in case others mistakenly step on the pedal switch caused clamp injury.
5. If you need to replace a wire stripper blade, power off and cut off the air before replacing it.
6. If any abnormality is found in use, power off immediately and notify dedicated maintenance personnel for maintenance.
7. During the operation, the operator should concentrate, and do nothing unrelated to production is strictly prohibited.
Three: the end of the homework
1. After the execution of the production plan, the power supply of the equipment shall be turned off;
2. Turn off the main power supply of the equipment and clean the machine and surroundings before going off work.
Current machine automation age is more and more popular, people must have been more and more high to the requirement of wiring harness processing equipment, and automatic wire stripping machine technology is already very mature, so good understand relevant knowledge of mechanical equipment is also very necessary, hope this piece of wire stripping machine safety operation procedures can help to you.
上一篇：
How to ope......
下一篇：
Safety ope......
Technical Support
Product
Home
- Home
- About RS
- Product
- Wire Harness Processing Center
- Solution For EV Cable
- Wires Twisting Machine
- Terminal Crimp& Tinning
- Wire Cut & Strip
- Wire Strip And Crimp
- Solution For Soldering
- Solution For Tube
- Twisted Wire Untwisting Machine
- Ancillary Equipments
- Solution For Braid/Sheath
- Solution For Cable Tie
- IDC Crimping
- Applicator & Crimping Tools
- Solution For Tape
- Solution For Seal/Sleeve Insertion
- Quality Tools
- Solution For Wire Splicing
- Project Applications
- MES System
- AGV Dispatching system
- Wiring Harness Assembling
- Lean Mangement Tube
- Wire Seal
- Lean Management Materials
- Spare Parts For Komax Machine
- Others
- Technical Support
- News
- Download
- Contact RS
|
|
NameDescriptionContent