How to operate semi-automatic terminal machine
Source: Author: rsautomation88 Publish time: 2022-05-26 18:01 878 Views
Semi-automatic terminal machine is the terminal of a very common type of processing equipment, relying on the running speed, the advantages of the simple, in line for machining scope is very broad, so has been recognized by the masses of users, on the market liquidity is very high, but there are still a lot of people did not know the specific operation process of semi-automatic terminal machine, Here we detail semi-automatic terminal machine is how to operate it!
Semi-automatic terminal machine is the terminal of a very common type of processing equipment, relying on the running speed, the advantages of the simple, in line for machining scope is very broad, so has been recognized by the masses of users, on the market liquidity is very high, but there are still a lot of people did not know the specific operation process of semi-automatic terminal machine, Here we detail semi-automatic terminal machine is how to operate it!
Semi-automatic terminal machine operation process:
1. Turn on the power switch of the terminal, and the power indicator is on.
2. Pay attention to whether there is obvious abnormal sound inside and outside the machine. If there is suspension of operation, please ask the mechanic to determine whether maintenance is needed.
3. Select and install the knife: By designated personnel operations, whether must be manually ratio on the selected blade knife before form a complete set, contrast and correct rear can with the knife knife installed finished, must use the manual test, first close the terminal mechanical and electrical source, cut touch button, use a dedicated plate loom, master-slave pulley, the terminal machine stamping trip to maximum, such as hand did not move, consider whether stress or other problems, Check and debug until qualified. Before operation, check the locking screws and make sure they are not loose.
4, loading: mount need a taxi terminal, use the Allen wrench to adjust feed clamp, the terminal can easily pass, visual feed position whether appropriate, if not, adjust, use the Allen wrench to loosen feeder lock screw, a screw dynamic adjustment Lei lever adjustment, until his best, and then lock feeder lock screw, began to work.
5, testing tension: after the machine OK, try take waste wire, tensile test, the main reference value to see the pull test table, the specific operation method is as follows, press the tension test the zero key to zero, will need to measure the terminal wire clamp, tested, if measured tension is beyond the scope of the standard, please mechanics to adjust, until reach the standard.
6. 10PCS in trial production shall be sent to the quality inspector for confirmation of the first piece. Only after passing the inspection, can mass production be carried out.
7, after the completion of production, sort out good products, waste and defective products, and clean up the environment around the machine.
If you want to know how the terminal machine works? You can read "terminal machine working principle full solution".
Semi-automatic terminal machine notes:
1. In the process of operation, if the machine is abnormal, turn off the power first, and ask the mechanic to repair and debug in time.
2. Non-designated personnel are strictly forbidden to debug or disassemble machine parts without permission.
3, during the operation, the power supply of the machine is not disconnected, fingers or any part of the body is prohibited to enter the stamping range, so as not to cause industrial accidents.
4. In operation, if you need to leave the job, you must turn off the power supply before leaving.
5. When replacing the terminal, disconnect the power supply before replacing the terminal. It is strictly prohibited to replace the terminal during the operation of the machine.
6. During the operation, if any terminal is stuck in the knife die, it is necessary to turn off the power and remove it with scissors or needle before continuing the operation.
The above is the specific operation process of semi-automatic terminal machine and relevant matters needing attention, if there is any doubt, consult in time.
Semi-automatic terminal machine operation process:
1. Turn on the power switch of the terminal, and the power indicator is on.
2. Pay attention to whether there is obvious abnormal sound inside and outside the machine. If there is suspension of operation, please ask the mechanic to determine whether maintenance is needed.
3. Select and install the knife: By designated personnel operations, whether must be manually ratio on the selected blade knife before form a complete set, contrast and correct rear can with the knife knife installed finished, must use the manual test, first close the terminal mechanical and electrical source, cut touch button, use a dedicated plate loom, master-slave pulley, the terminal machine stamping trip to maximum, such as hand did not move, consider whether stress or other problems, Check and debug until qualified. Before operation, check the locking screws and make sure they are not loose.
4, loading: mount need a taxi terminal, use the Allen wrench to adjust feed clamp, the terminal can easily pass, visual feed position whether appropriate, if not, adjust, use the Allen wrench to loosen feeder lock screw, a screw dynamic adjustment Lei lever adjustment, until his best, and then lock feeder lock screw, began to work.
5, testing tension: after the machine OK, try take waste wire, tensile test, the main reference value to see the pull test table, the specific operation method is as follows, press the tension test the zero key to zero, will need to measure the terminal wire clamp, tested, if measured tension is beyond the scope of the standard, please mechanics to adjust, until reach the standard.
6. 10PCS in trial production shall be sent to the quality inspector for confirmation of the first piece. Only after passing the inspection, can mass production be carried out.
7, after the completion of production, sort out good products, waste and defective products, and clean up the environment around the machine.
If you want to know how the terminal machine works? You can read "terminal machine working principle full solution".
Semi-automatic terminal machine notes:
1. In the process of operation, if the machine is abnormal, turn off the power first, and ask the mechanic to repair and debug in time.
2. Non-designated personnel are strictly forbidden to debug or disassemble machine parts without permission.
3, during the operation, the power supply of the machine is not disconnected, fingers or any part of the body is prohibited to enter the stamping range, so as not to cause industrial accidents.
4. In operation, if you need to leave the job, you must turn off the power supply before leaving.
5. When replacing the terminal, disconnect the power supply before replacing the terminal. It is strictly prohibited to replace the terminal during the operation of the machine.
6. During the operation, if any terminal is stuck in the knife die, it is necessary to turn off the power and remove it with scissors or needle before continuing the operation.
The above is the specific operation process of semi-automatic terminal machine and relevant matters needing attention, if there is any doubt, consult in time.
上一篇：
Safety ope......
下一篇：
Safety ope......
Technical Support
Product
Home
- Home
- About RS
- Product
- Wire Harness Processing Center
- Solution For EV Cable
- Wires Twisting Machine
- Terminal Crimp& Tinning
- Wire Cut & Strip
- Wire Strip And Crimp
- Solution For Soldering
- Solution For Tube
- Twisted Wire Untwisting Machine
- Ancillary Equipments
- Solution For Braid/Sheath
- Solution For Cable Tie
- IDC Crimping
- Applicator & Crimping Tools
- Solution For Tape
- Solution For Seal/Sleeve Insertion
- Quality Tools
- Solution For Wire Splicing
- Project Applications
- MES System
- AGV Dispatching system
- Wiring Harness Assembling
- Lean Mangement Tube
- Wire Seal
- Lean Management Materials
- Spare Parts For Komax Machine
- Others
- Technical Support
- News
- Download
- Contact RS
|
|
NameDescriptionContent