Code of safe operation for skinning machine
Source: Author: rsautomation88 Publish time: 2022-05-26 17:59 469 Views
Wire stripping machine just as its name implies is dedicated to the processing wire the separation of skin and core line a mechanical equipment, can adjust the combination and arrangement of the cutting tool according to the wire, so the machining scope is large, when processing as long as can production, gas source on is a very practical wiring harness processing equipment, and what are the specific operation peeling machine? Let silver steel to give us a careful explanation of the peeling machine safety operation procedures!
Wire stripping machine just as its name implies is dedicated to the processing wire the separation of skin and core line a mechanical equipment, can adjust the combination and arrangement of the cutting tool according to the wire, so the machining scope is large, when processing as long as can production, gas source on is a very practical wiring harness processing equipment, and what are the specific operation peeling machine? Let silver steel to give us a careful explanation of the peeling machine safety operation procedures!
Operation method:
1, boot, check whether the operation is normal, feed according to the size of the cable diameter, one by one into the corresponding feed hole;
2. In order to ensure the durability of the blade, the joints of the rubber and plastic cable should be cut off when feeding, so as not to break the blade;
3. If there is too deep and broken wire after feeding, pay attention to the following conditions:
(1) The feed gear should be adjusted, that is, the tension of the spring pressure on both sides of the blade shaft;
(2). Check whether the feeding hole position is misplaced when feeding;
(3). If the blade is too sharp, apply the grindstone to trim it slightly until it is moderate.
4, if the feed, the skin has been peeled, but the copper wire can not be exposed. The main cases are as follows:
(1) the upper shaft klyling is too deep, the application of grindstone to repair the upper shaft, but not too much repair, too much repair is easy to cause oily cable is difficult to drive;
(2). Whether the spring pressure is too loose, the pressure should be tightened;
(3) wire diameter is small, or the upper and lower shaft clearance is more, appropriate adjustment of the two shaft clearance;
(4). The processed cable has been heated, and the copper wire will not be easily exposed to the skin.
5, if after feeding, the rolling file can not drive the cable to the past, the material stays in the middle, there are the following situations:
(1). Check whether the belt of each gear is loose;
(2) check whether the spring pressure on both sides of each gear is too tight, there is no top force, the pressure should be relaxed;
(3) The cable is too oily, so that the two shafts slip, and the two shafts should be cleaned regularly.
The above is the safety operation rules of the peeling machine, the practicality of the peeling machine is very high, the price is not expensive, as long as you understand the specific operation of the peeling machine can be quickly put into production.
Operation method:
1, boot, check whether the operation is normal, feed according to the size of the cable diameter, one by one into the corresponding feed hole;
2. In order to ensure the durability of the blade, the joints of the rubber and plastic cable should be cut off when feeding, so as not to break the blade;
3. If there is too deep and broken wire after feeding, pay attention to the following conditions:
(1) The feed gear should be adjusted, that is, the tension of the spring pressure on both sides of the blade shaft;
(2). Check whether the feeding hole position is misplaced when feeding;
(3). If the blade is too sharp, apply the grindstone to trim it slightly until it is moderate.
4, if the feed, the skin has been peeled, but the copper wire can not be exposed. The main cases are as follows:
(1) the upper shaft klyling is too deep, the application of grindstone to repair the upper shaft, but not too much repair, too much repair is easy to cause oily cable is difficult to drive;
(2). Whether the spring pressure is too loose, the pressure should be tightened;
(3) wire diameter is small, or the upper and lower shaft clearance is more, appropriate adjustment of the two shaft clearance;
(4). The processed cable has been heated, and the copper wire will not be easily exposed to the skin.
5, if after feeding, the rolling file can not drive the cable to the past, the material stays in the middle, there are the following situations:
(1). Check whether the belt of each gear is loose;
(2) check whether the spring pressure on both sides of each gear is too tight, there is no top force, the pressure should be relaxed;
(3) The cable is too oily, so that the two shafts slip, and the two shafts should be cleaned regularly.
The above is the safety operation rules of the peeling machine, the practicality of the peeling machine is very high, the price is not expensive, as long as you understand the specific operation of the peeling machine can be quickly put into production.
上一篇：
Safety ope......
下一篇：
Daily trou......
Technical Support
Product
Home
- Home
- About RS
- Product
- Wire Harness Processing Center
- Solution For EV Cable
- Wires Twisting Machine
- Terminal Crimp& Tinning
- Wire Cut & Strip
- Wire Strip And Crimp
- Solution For Soldering
- Solution For Tube
- Twisted Wire Untwisting Machine
- Ancillary Equipments
- Solution For Braid/Sheath
- Solution For Cable Tie
- IDC Crimping
- Applicator & Crimping Tools
- Solution For Tape
- Solution For Seal/Sleeve Insertion
- Quality Tools
- Solution For Wire Splicing
- Project Applications
- MES System
- AGV Dispatching system
- Wiring Harness Assembling
- Lean Mangement Tube
- Wire Seal
- Lean Management Materials
- Spare Parts For Komax Machine
- Others
- Technical Support
- News
- Download
- Contact RS
|
|
NameDescriptionContent